Wakeonlan over the internet4/25/2023 The first thing we are going to do is follow these steps: If the operating system is not compatible with WoL or we do not have it properly configured, we will not be able to use it. Configure the operating systemĪs we have already commented previously, not everything has to do with the hardware of our equipment. Finally, in modern equipment sometimes it is not necessary to configure anything and we can use Wake on WAN without having to touch anything, because it is already preconfigured at the factory. As each manufacturer names them differently, and also to access the BIOS / UEFI is different, it is advisable to consult the motherboard manual in case we have doubts. Other names they may receive are Wake on Lan, WOL, Remote Wake Up, and Wake on Magic Packet. There for it to work we had to activate the PCI Devices Power On and Ring-In Power On options. In the case of the BIOS that I have used it is called ACPI Configuration. The options that we must enable are usually found in a section called Power Management or similar, although it also receives other names. If we want to access the BIOS / UEFI of our computer as soon as we start it, it is usually accessed by pressing the F2 or DEL keys. In addition, it is totally necessary to make several previous configurations, such as checking in the BIOS / UEFI that the Wake on LAN we have activated, the operating system supports this type of technology and configuring it correctly, and, finally, configuring our router correctly. The process of configuring Wake on WAN is similar to configuring Wake on LAN, but we have to open a certain port on our router and redirect it to our PC that we want to open. Wake on WAN configuration to remotely turn on computers Once we have seen what Wake on WAN is, we are going to see how the complete configuration would be done to turn on your PC remotely. By having our computer only on when necessary, we can keep it off until we need it. Energy savings that will translate into a lower electricity bill.This is something very positive if at any time we are away from home or the office, and we want to access our files or use a program that we have on our computer. We can turn on the equipment from anywhere remotely, as long as we have an Internet connection.Click OK.Īfter the above configuration, you can now launch a third-party WOL software on PC B and send a Magic Packet to boot up PC A. Specify the internal server IP as 192.168.0.100, which is the IP address of PC A. Specify the external port and internal port as 7, which is used to receive Magic Packets. Specify the WAN port according to the network environment. Click OK.Ĭhoose the menu Transmission > NAT > Virtual Servers and click to load the following page. Enter the IP address and MAC address of PC A. If there is not a desired entry, click to load the following page. Check if the desired IP address is reserved for PC A. Click OK.Ĭhoose the menu Network > LAN > Address Reservation to load the following page. Enable Export to DHCP Address Reservation. In the IP-MAC Binding List section, click to load the following page. In the Scanning Result section, click the corresponding to bind MAC and IP address of PC A.Ĭhoose the menu Firewall > Anti ARP Spoofing > IP-MAC Binding to load the following page. Wait a minute until the scanning is completed. In the general section, specify the scanning IP range according to the DHCP address pool. If the desired entry is in the list, click the corresponding to bind MAC and IP address of PC A.Ĭhoose the menu Firewall > Anti ARP Spoofing > ARP Scanning to load the following page. There are three methods to do IP-MAC binding: bind in the ARP list, bind in ARP scanning result, or add IP-MAC Binding list entry manually.Ĭhoose the menu Firewall > Anti ARP Spoofing > ARP List to load the following page. To achieve this requirement, you can configure the router as follows:Īfter you complete the configuration, you can use a WOL software to wake up PC A on PC B.įollow the steps below to configure the router.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |